Unit  Dimension : - 38 x 22.5 x 12 mm / 1.5 x 0.9 x 0.5 inch(L*W*H); Voltage: 12V; Force: 42N; Current: 1A;  Stroke : 10mm / 0.39 inch;  

Unit Feature:
C type push solenoid has a push bar attached to the curved head of the plunger and when the plunger is pulled into the solenoid the push bar extends out the opposite end.The C Type Push solenoids have a return spring in place to return the plunger to a fixed position when no other force is applied to the plunger.The force applied by the return spring is included in the pull force – stroke relationship graph to the right.

It is a stable performance and 300000 lifespan cycles for base application.

Maintains the open / closed state of the solenoid with short-time   energization, and achieves low power consumption by using a permanent magnet.

Power Source :  DC power-operated 12V   

Push pull type, linear motion, plunger return, DC solenoid electromagnet.

Solenoids of this category work externally through pulling pushing in plunger.

When energized, doing work through pulling pushing in plunger joined object.

DC Frame type Solenoid Electromagnet mainly used in vending machines, transport equipment, office facility household appliance, mechanical, etc.

Metal Housing:  Carbon Steel housing, It is electroplated with Zinc or Nickle coating. It is undergone 96 hours salt spray testing and it is anticorrosion with high temperature standard and compliance with RoHS. 
Metal Plunger:  Carbon Steel material, It is electroplated with Zinc coating with smooth surface. It is passed 96 hours salt spray testing and it is anticorrosion and compliance with RoHS Standard. 

Heat dissipation

The feature of the frame type solenoid is easier to dissipate compared with the round type, tubular type and the suction cup electromagnet. Most of its bobbin copper coils are exposed to the outside, which can discharge the heat in time to make sure smoothness in work, without jamming, stopping or burning situation.. Therefore, the frame type solenoid is popular in good quality and has good heat dissipation capacity. 

Advantages

AS 1031 Solenoid is a miniature push-pull electromagnet mass-produced by Dr. Solenoid at 2020.  The frame type electromagnet of AS 1031 can be made into a push electromagnet and a pull solenoid as per your specification. The product has small size, easy installation, low cost and is widely used in the market for automation equipment, automatic toys, medical mailboxes and lockers, etc.

As 1037 of Push pull Type Solenoid, it is linear motion, frame type, plunger spring return and low power consumption with reliable temperature rise. 

Unit Advantage: -  D frame Push Pull type Solenoid electromagnet has simple structure, small volume production, high adsorption force. Pure copper coil with good conduction and insulation inside. It has high temperature resistance features. 

D Frame type Solenoid Application:  DC 24V solenoid electromagnet are widely used in vending machines, transport equipment, office equipment,  facility household appliance, mechanical, etc  game machine, Sorting machine, auto door lock, etc.it is simple design and easy installation and operation. 

Lifespan: 

The unit lifespan can reach 200,000 cycles times, which can meet the long-term use of the machine and does not need to be replaced frequently. It bringing great convenience to the machine in term of service .  During product development period, the specification and  the lifespan service has been validation by our R & D team.  Therefore, we can make sure you in  safety, quality and production efficiency for AS 1037 model. 

DC Solenoid is a linear push pull type solenoid features D or C type frame structure design, Stroke Force as well as the plunger are adjustable accordingly. It is widely application in medical device, automotive equipment and smart household appliance. 

AS for the DC source power, we have DC 6 V, 12V, 24 V and 36 V standard voltage optional. Custom solutions for changing the size of Frame, stroke, the copper coil and the duty cycle, mounted screw hole, value package available. 

Unit Features: 

Housing Steel:  Carbon steel with Zinc Coating, Smooth surface, Rohs Compliance 
Plunger: φ10 mm, Carbon steel with Zinc Coating Anticorrosion., Meet Rohs compliance. 
Voltage: DC24V 
Stroke: 0-10mm, we can change the distance accordingly. 
Force: 2-15N adjustable , 
Power Wattage: 9 W 
Current: 0.75A
Resistance: 16 Ω
Life: ≥200,000 times, has been validation during product development
Working Cycle: 1s On, 1s Off
Temperature Rise : 65 degrees Cel.

Our R & D Team: 

Our R & D team offer one-stop solenoid & Solenoid Valves solutions according to Customer specification.  we consider the using condition to select the best material, make the engineering drawings for dimension and confirmation before creating the working sampling; trying our best to minimize the time waste and accelerate the timetable of launching new product for you. For more details, Pls contact our sales expert today. 

Unit Dimension: 56  x 32 x 23 mm / 2.2 x 1.26 x 0.91 inch (L*W*H); Voltage: 24V; 

Introduction of Open Frame Solenoid:

Linear Open-Frame Solenoids are available in various designs, as Pull, Thrust (Push) or a combination type, which offer a simple and robust action for the industry and automation equipment.
We can make both AC or the DC power sources ;  DC Voltage ; 6 V , 12 V ,24 V  36 V ,48 and 60 V .    AC Voltage: 110V, 115V & 230V.
Custom AC & DC voltages available on request for your specification. 
Long stroke designs for improved performance over greater strokes.
Electric wire fitted 200mm as standard.
Optional return springs or the mounted screw holes. 
Fixing arrangement, plunger coupling, thrust rod options and lead length can all be customize

Unit Features:

DC24V  Push pull Type, linear motion, frame type, plunger spring return, Low power consumption to ensure high efficiency and 300,000 cycle lifespan. 
D Type Frame Solenoid electromagnet has simple structure, small volume, high adsorption force. Good copper coil inside, has good temperature resistant performance along with high electrical conductivity.
Standard working condition: Ambient Temperature: 20±2℃, Relative Humidity: 65±5%RH  
Product Standards ● designed and tested to VDE 0580 ● manufactured to ISO 9001

Material Selection:

Solenoid Enclosures : We offers two types of enclosures, each for a variety of applications: a one-piece molded epoxy construction called the Red Hat II solenoid and a conventional Red Hat metallic construction.  Both meet ICS-6 ANSI/NEMA, and UL Standards 429, 508, and/or 1002. These standards define enclosure protection levels and the tests passed to earn each Type designation

Application:

The Pull push type, linear motion open frame, plunger spring return, DC solenoid electromagnet of Dr. Solenoid are wildly used in vending machines, transporting equipment, office device; smart household appliance, mechanical used. 
Notice: please take the electromagnet put down gently when you install it. The screw thread can make a corresponding change according to your demand. This product is small in size, please pay attention to in the process of using electricity, so as not to damage the electromagnet.

Unit Dimension: Diameter 50, High 30 Mm

Principle of AS 5030 holding sucker solenoid: 

As 5030 electromagnetic holding magnets are magnetized when current is applied, providing a reliable solution for applications where significant holding force and low power consumption is required. 
The holding sucker Solenoid can be designed as IP waterproof structure or conventional structure along with high temperature resistant type. The smallest electric suction cup can be made 5 mm in diameter and the largest can be 500 mm. The magnetic field is completely closed during operation, with strong suction force, no magnetic leakage, and no impact on surrounding electronic device. t

Benefit 

Compact design and water-proof body.
Optimized power consumption and low rest magnetism 
Maximum holding force with low air gaps 
Armature keeper plates available 
Dual-fixing • High quality, cost effective package

Unit Features: 

Available in a range of Solenoid sizes from Ø15 to Ø180 mm 
Axial forces ranging from 40 to 40,000N 
Special voltages/forces/mountings available on request. 

Key Applications

Automation, transportation and handling 
Door locking/holding mechanisms for access control and security 
• Fixture construction 
• Medical applications 
• Wind turbines in the renewable energy sector 

Note for Using this Electromagnets

When using a holding electromagnet, it is important to ensure that it is connected to a control system that allows for control and management of the magnet. It is also important to ensure proper installation to ensure that the electromagnet is properly positioned and can be effectively utilized.
The use of a holding electromagnet can bring many benefits to industrial processes and security systems. It improves workplace safety, speeds up processes, and increases work efficiency.

Unit Dimension: φ 13 *25 mm / 0.54 * 1.0 Inches.  Stroke Distance: 6-8 Mm  ; 

What is the Tubular Solenoid? 

The purpose of tubular Solenoid is to get the maximum power output at the minimum weight and limit size. Its features include small size but large power output, Through the special tubular design, we will minimize the magnetic leakage and lower the operating noise for your ideal project.  Based on the movement and Mechanism, you are welcomed to choose the pull or push type tubular solenoid according. 

Product Features: 

Stroke distance is set up to 30mm (depending on tubular type) holding force is fixed up to 2,000N (in end position, when energized ) It can be design as push-type or tubular pull-type linear solenoid Long lifespan service: up to 3 million cycles and more fast response time: switching time < 2 ms possible (depending on size) standard tubular sizes from 11mm to 874mm diameter available. 
High Carbon steel housing with smooth and shining surface. 
Pure copper coil inside for good conduction and insulation. 

Typical Applications 

Laboratory Instrumentation 
Laser Marking Equipment
Parcel Collection Points
Process Control Equipment
Locker & Vending Security
High Security Locks
Diagnostic & Analysis Equipment

The type of Tubular Solenoid: 

Tubular solenoids provide an extended stroke range without compromising on force when compared to other linear frame solenoids. They are available as push tubular solenoids or pull tubular solenoids, in push solenoids 
the plunger is extended outward when current is on, whilst in pull solenoids the plunger is retracted inward.

What is DC Solenoid Tubular Type ? 

DC solenoids tubular type can custom the DC voltages between 3-24V and force up from 5 to 50N. The push and pull force can be significantly increased with limited energized time and with connection to big and high voltage. The DC solenoids tubular type is set up with a return spring inside, and are available in various construction types such as open, tubular, self-holding latching bistable and holding magnet designs. All DC solenoids tubular are available in mechanical pull L or push S designs and can be customized per specification. Common customizations like voltage , copper coil,plunger housing are mechanical as well as cable connections and cabling. 

Powerful and compact.

Smooth and flat surface.

Low consumption and reliable temperature rise

Ambient temperature within 130 degrees.

Electromagnet in working condition would produce a certain amount of heat, electricity more frequently the higher temperature, which is a normal phenomenon.

Dimension: 30 * 22 MM

Holding Force : 4.0 KG-150KG

Wire length is about 210mm

Electric lifting magnet.

Powerful and compact.

Smooth and flat surface.

Low consumption and reliable temperature rise

Ambient temperature within 130 degrees.

Electromagnet in working condition would produce a certain amount of heat, electricity more frequently the higher temperature, which is a normal phenomenon.

Feature

1. The adsorbed object must be iron;
2. Select the correct voltage and product model;
3. The contact surface is smooth, flat and clean;
4. The surface of the magnet must be closely attached to the adsorbed object without any gap;
5. The area of the adsorbed object shall be greater than or equal to the maximum diameter of the magnet;
6. The object to be sucked must be close, the middle can't be interspersed with objects or gaps (Contrary to any conditions, suction will be reduced, not the maximum suction.)

Unit Dimension: 36 x 28 x 26 mm / 1.04 x 1.42 x 1.59 inch (L*W*H); Voltage: 6 V;    Force: 2 N; Current: 0/6 A; Stroke : 6 mm 

Principle of Flapper Solenoid: 

A flapper solenoid is made with a copper coil, moving plunger and a special design flap, When the electric current passes through copper coil, the plunger retracts. When the current stops passing, the plunger goes back to the previous position with the help of a spring.
With this simple mechanism, the solenoid controls the motion of the flap that connects to the plunger. The flapper solenoid, therefore, gets to control the operation of any mechanical devices attached to it, such as gear sets or a cam mechanism. 

Features:

DC Voltage： DC 6.0 V 
Stroke： 6 mm Force：
keep force > 2 N  
Work Mode：knocking 
Insulation class： Class B，F..... 
Noise：<60dB @ no load 
Power Wattage:  7.2 W
Rate Current:  0.5 A
Resistance: 20 Ω
Lifespan Service : ≥100,000 times 
Working Cycle: 0.5s On, 2s Off

Flapper Solenoid Application: 

The common application of flapper solenoids are used in the copy machines, printing machines, massager chair and other massager product, cotter joint devices, etc.  

What we have and what we can do for you. 

Our international and domestic DC solenoids include open frame solenoids, flapper solenoids
Sucker solenoid, tubular solenoids and special & valve solenoids. If a standard solenoid does not fit your existing project, contact our sales expert for custom solenoid solution options. Solenoids can be designed to meet your specs and are guaranteed maximum function and cost efficiency. Our R & D capabilities include design, development, sample production and first article approval with full documentation. All of our products are 100% tested before shipment, our company are a ISO 9001-2015 certified and RoHS Compliant also. 

Unit Dimension: Diameter 20, High 22 Mm

Principle of Holding sucker Solenoid

this type of round electromagnets, the attraction is created when the holding sucker solenoid is powered on. When the power supply is off, the part being held is released.  The Diameters of holding sucker solenoid is made between 20 and 150 mm in standard manufacture.

Unit Features: 

Powerful and compact Design 
Housing Material: Good Carbon Steel with Zinc or Nickle coating. Smooth surface and Rohs Compliance
Input Voltage:  DC V 
Peak Force:250N
Holding Force: 185N
Duty-cycle: 50%;
Electric time: Less than 7 minutes;

Electric Lifting Magnet Applications

Electric Lifting Magnets are versatile tools used across various settings, including automation assembly lines, sorting machines, mechanical arms for robot machine, and experimental facilities. It's important to note that factors such as prolonged operation, lower voltage, and unsuitable materials can reduce the magnet's force. For optimal performance and safety, it's advised to utilize the magnet at no more than 80% of its rated lifting capacity as indicated on the nameplate.

Caution of Using this Electromagnets

1. The relative object absorbed must be a good magnetic material
2. The suction surface of the electromagnet must be smooth and clean.
3. The thickness of the object is 5 mm at best.
4. The contact surface of the object must be larger than the adsorption surface of the electromagnet

Working Principle

The operation of a tubular solenoid depends on the principles of electromagnetism. When an electric current is passed through the copper coil wire, it produces a magnetic field around the copper coil wire. By coiling the wire, the magnetic field inside the coil is intensified. Once the copper coil is energized, the magnetic field generated pulls or pushes the plunger forward. The strength of the magnetic field, and thus the force exerted on the plunger, is proportional to the amount of current flowing through the coil. This allows for precise control of the solenoid’s movement, making it ideal for applications that require high precision and reliability. 

Product Features: 

Housing Case :  Carbon steel housing with electroplated coating, high shining and smooth surface, RoHs and Reach compliance. 
Plunger: φ12mm  Carbon steel material
Voltage: DC 24 V 
Stroke:  10  mm (adjustable ) 
Force:  300 Gf
Power: 3.6 W
Current: 1.6 A
Resistance: 50 Ω
Lifespan cycles: ≥200,000 times
Working Cycle: 0.1s On, 1s Of

AS 3864 Tubular solenoids featuring a 1.49 in. diameter have a 2.52 in. long housing The captive plunger or actuator has a diameter of 0.39 in. and a stroke of 0.39.  A glass-filled nylon bearing and the electrodes nickel-plated plungers contribute to the exceptionally long life of these compact solenoids.  Plungers are spring-loaded and have fully rounded tips, making them ideal for being used as miniature latches.
AS 3864 Solenoid coils typically utilize Class “F” 23 to 40 AWG (American Wire Gauge) windings with Class “A” insulation for better protection of the solenoid during longer duty cycles.
These clean, high efficiency, low cost, precise tubular solenoids can be operated at 1/10, 1/4, 1/2, and continuous duty cycles (voltage dependent) and are the ideal choice for Medical dispensing, mixing, vending machines, valve control, farm machinery, disconnects, transmission shifting, toys, fire suppression systems, cabinet locks, latching, door controls, and sorting equipment.  An optional, compact clamp permits easy installation and allows for precise linear positioning of the solenoids.  

Unit Dimension: Diameter 40, High 25 Mm; 

The Holding sucker Solenoid Principle

The principle design of holding sucker solenoid is to maintain electromagnetic attraction when the power on. Once the power is off, the electromagnet will lose its attraction and release the object accordingly. The standard model of this holding sucker solenoid has an outer diameter range from 20mm-150mm.

Unit Feature:

Compact and powerful Design 
Body Material: High Carbon Steel with Zinc coating. Smooth surface and Rohs Compliance, anticorrosion also. 
Power Source:  DC 24 V 
Peak Force: 300N
Holding Force: 200 N
Duty-cycle: 50%;
Electric time: Less than 7 minutes ;

Electric Lifting Magnet Applications

The Electric Lifting Magnet solenoid are wildly applied  to intelligent robots, traditional manipulators for grasping magnetic work pieces, ore sorting machines, and brakes for various rotary mechanisms.

Caution when using the Electric Lifting Magnet solenoid

1.The object should be a well magnetic material.
2. The object surface of the electromagnet should bed smooth.
3. The best thickness of object is better to do with 5 mm..
4. The contacted surface of the object must be bigger or large than the adsorption surface of the electromagnet

We help you make the perfect Electric Lifting Magnet Solenoid 

Our R & D team is professionals in the design and manufacture of solenoid. We are always available to listen to your needs and help you find the most suitable solenoid for your project You can also customize your equipment to make it even more practical and versatile, tailored to your objectives. Contact us for a free quote. 

Dimension: φ 45 * 45 mm / 1.93 * 3.94 Inches.  Stroke Distance:  Mm ; 8-10 MM 

Principle of Tubular Solenoid 

The tubular solenoids ‘s structure is a direct-acting push and pull movement with a unique tubular shell design. The stable and smooth product surface ensures its softness and flexibility during operation.  We can make The diameter of tubular shell from 11mm to 70mm, Its characteristics are: long lifespan with 300,000 cycle time, quiet operation, fast response, stable action, and no radial vibration

Features :  

Unit Housing: Stainless steel housing enclosure, high shining and smooth surface, RoHs and Reach compliance. 
Plunger: φ10 mm  Carbon steel material
Voltage: DC24 V 
Stroke:  4 mm (adjustable according to the requirement) 
Force:  3 Kg
Power: 32 W
Current: 1.33 A
Resistance: 13.8 Ω
Lifespan cycles: ≥200,000 strokes
Temperature rise: max 65 degrees . Cel. 
Working Cycle: 1 s On, 3s Of

Application: 

It is suitable for all kinds of electric toys, office equipment, household appliances, etc. It can be designed into three structures: pull-type electromagnet/push-type electromagnet/push-pull electromagnet. It has the characteristics of simple structure and reliable action. The movable iron core connection part can be designed into various types to match your project. It is also called tubular electromagnet and tubular solenoid. Push-type means that the slide bar is attracted when the product is powered on, and the top rod on the slide bar is used to push the object. Pull-type means that the slide bar pulls the object when the product is powered on. It is designed according to the actual needs of the customer, and the push-pull force can generally be achieved. Usually, the small push-pull round tube electromagnet T2045 is used in life test equipment, electronic toys, etc.

Dimension: φ49 *100 mm / 1.93 * 3.94 Inches.  Stroke Distance: 13 mm.

Principle of Tubular Solenoid: 

Tubular solenoid is the same like the frames and round steel tubes.  This is based on the movable iron core, 
fixed iron core, electromagnetic coil, etc. inside the electromagnet. When it is plugged in, Finally, a process of pushing or pulling occurs. it is a piston-like movement.

Features:

Tubular Housing: Carbon steel housing enclosure, high shining and smooth surface, Rohs and Reach compliance standard.
Plunger: φ10 mm  Carbon steel material
Voltage: DC24 V 
Stroke:  8 mm (adjustable according to the requirement) 
Force:  3 Kg
Power: 48 W
Current: 1.8 A
Resistance: 13.8 Ω
Lifespan cycles: ≥200,000 strokes
Temperature rise: max 65 degrees . Cel. 
Working Cycle: 1 s On, 3s Of

Custom Design : 

We are able to customize various types of tubular solenoid at, small push-pull solenoid, and push-pull solenoid. If you have relevant push-pull tubular solenoid like AS 4910 drawings or technical requirements, parameter requirements, processing requirements,,  our professional R & D team can make your requirements according to your product application needs. At present, 97% of customers are non-standard customizations, and a small number of customers have conventional products.  As for your project and the design, pls contact us with your specification. 

What is Tubular Solenoid? 

Our tubular solenoids go in two basic types, namely, the pull-type and push-type tubular solenoid. Both are designed to offer the same functional characteristics. While Energized, the plunger is stopped at the end, preventing a collision with the fixed core, smaller impact noise and absence of residual magnetism.

Unit Features: 

Tubular Housing Shell: Stainless steel housing enclosure, high shining and smooth surface, RoHs and Reach compliance. 
Plunger: φ10 mm  Carbon steel material
Voltage: DC24 V 
Stroke:  4 mm ( adjustable ) 
Force:  1000 Gf
Power: 47 W
Current: 1.74 A
Resistance: 13.8 Ω
Lifespan cycles: ≥200,000 times
Working Cycle: 0.1s On, 1s Of

DESIGN-  Tubular Pull type, linear motion, open frame, plunger spring return, DC 24 V solenoid electromagnet.        All metal parts has down with 96 hours salt spraying testing and meet RoHS requirement. 

ADVANTAGES- Simple structure, small volume, high adsorption force copper coil inside, has good temperature stability and insulation, high electrical conductivity. Less power consumption, low temperature rise, no magnetism when power off.  It can be installed flexibly and quickly, which is very convenient.

APPLICATION:  DC Tubular solenoid electromagnet use in vending machines, transport equipment, office facility household appliance, mechanical, etc game machine, Sorting machine, door lock, etc.

NOTED:  As an actuating element of animation equipment ,because the current is large, the single cycle can not be electrified for a long time. The best operate time is in 2 seconds.